Kingfisher Electric Boats Products Page

Electric Fishing Kayak Kits and Plans

Products :

: Kingfisher-10 Kayak Building Plans with Maintenance and Operations Sections; A detailed building plan with many pictures to make assembly as simple as possible. It also includes an operation and maintenance section.
135.00 with FREE Domestic Shipping (International buyers contact us for shipping cost)
: Kingfisher-10 Controller; Controller comes as a plug and play unit. It gives the Kingfisher Kayak the unique ability to go forward/backward, left/right, and stop/start - hands free
330.00 with FREE Domestic Shipping (International buyers contact us for shipping cost)
: Kingfisher Kayak Frame Kit; The frame kit contains all frames stringers and internal parts needed to build the boat ready to place skin panels.; 856.00 with FREE Domestic Shipping (International buyers contact us for shipping cost)

: Kingfisher Electrical Kit; The electrical kit is plug and play being very simple to install. No soldering or wiring is required, just mount the harness and plug it in.; 215.00 with FREE Domestic Shipping (International buyers contact us for shipping cost)

Kingfisher-10 Motor; This is a Minkotta Endure, 40 Motor that has been modified to specifically use with the Kingfisher-10 Kayak.
325.00 with FREE Domestic Shipping (International buyers contact us for shipping cost); Kingfisher Complete Building Kit; This complete building kit includes most everything you need to construct your Kingfisher-10 Kayak. We do not include the skins, as at this time we have shipping restraints due to the length of the pieces.
1843.00 with FREE Domestic Shipping (International buyers contact us for shipping cost); Kayak Kits and Parts Price List

Build your KF-10 with confidence

The KF10 is offered as a kit boat with all parts available except the skin and finish material. The skin panels (4 x 8 ft) are too large to package and ship. We have left these for the builder to purchase locally. The frame of the boat is first constructed with provisions for installation of all parts completed. then the skin is then placed on the frame. The skin panels are designed so that precise cutting of the material is avoided, and ordinary tools and skills give good results. The skin is then covered with 4 oz. fiber glass for additional strength. Finally the motor and electrics are installed to complete the job.

The Construction/Operation and Maintenance manual provides over 100 pages of text, pictures and drawings of all of the parts that make up the boat. Schematics and assembly drawings of electrical assemblies are provided so you can fabricate these, or you can purchase them ready to install. The critical parts of the frame are full sized drawings and are easily transferred to wood making the construction of the frame easy and accurate. Step by step instructions are provided so that builders can avoid most of the pitfalls boat builders face. The Motor Control Unit is not a kit, but a component that must be ordered from Kingfisher Electric Boats.

Building Options

Option 1 -DIY

Purchase the Manual and Motor Controller Unit. Find, fabricate or scrounge all of the material and parts called for in the manual. Assemble the boat from these. The time required will vary depending upon your gathering skills, but figure around 100 + hours.

Option 2 (less expensive)

Purchase parts and kits in the table below and assemble smaller assemblies as instructed in the manual. Build the boat. Time required approximately 100 hours but less than option 1. See Table 2 below.

Option 3 (a little more money, a lot less time)

Order kits in the following table. Notice the electrical kit, modified motor, control panel and steering hardware are assembled and either installed (Frame 2 pedal assembly) or ready to install. All are tested and insure a trouble-free boat. Build time about 70 hours. See Table 3 below.

Option 4 (Bend the Budget - fastest way)

The KF10 is available as a completely constructed boat. It and the manual is crated and shipped to your home ready to mount the included motor. Buy yourself a PFD, a paddle and a battery to power the boat. Get your gear and head for the water. Be sure to have someone read the operation section of the manual to you while traveling to the lake.

Option 1 - electrical Material From Kingfisher Electric Boats

Time to Build: 100+ hours

KF-10 Builders Manual	135.00
Motor Controller This is the Electronics Smarts, Motor Protection and Speed Controller	330.00
Sub Total	465.00

Option 1 - building materials purchased locally

Option 2 - Materials from Kingfisher Electric Boats

time to build: 100 hours

KF-10 Builders Manual	135.00
Motor Controller This is the Electronics Smarts, Motor Protection and Speed Controller	330.00
KF-10 Electrical Kit Pre-wired and tested signal and power wiring harness which includes the Control Panel and Power Circuit Breaker	215.00
KF-10 Backbone 3 pieces	120.00
Steering Cable Parts	50.00
Tiller Bracket Parts	31.00
Motor tilt Clamp	3.00
Cable Guides- transom 2 ea.	30.00
Pedal Parts for F-2, 2 ea.	52.00
Sensors parts for F-2, 2 ea.	68.50
Sub Total	1055.00

Option 2 - Parts Purchased Locally or From Suggested Vendors

Misc. Fasteners	20.00
11 Yards of 4 oz. 31 inch fiberglass	40.00
1 gallon resin or epoxy	40.00 (or 90.00 for epoxy
7-8 oz. of Cabosile thickener	10.00
3 sheets 4 mm Okoume plywood	120.00
1 sheet 12 mm Okoume plywood	100.00
Minn-Kotta Endura-40 motor (Walmart)	160.00
Sub Total	490.00
From Kingfisher Electric Boats	1055.00
Grand Total	1545.00
Time to Build	100 Hours

Option 3 - Materials from Kingfisher Electric boats

time to build: 70 hours

KF-10 Builders Manual

135.00

Motor Controller

The Electronics Smarts, Motor Protection and Speed Controller

330.00

KF-10 Electrical Kit

Pre-wired and tested signal and power wiring harness which includes

the Control Panel and Power Circuit Breaker

215.00

Frame Kit

All Frames +F2, F7 with hardware and steering cables

856.00

Modified Motor - Includes Tiller Bracket

325.00

Total from Kingfisher Electric Boats

1861.00

1861.00

Purchased Locally:

4 mm Okoume Plywood 3 Sheets

120.00

Fasteners, fiberglass, resin & Cabosile

170.00

Total from Kingfisher Electric Boats

1861.00

Total Option 3

2057.00

The difference between the Highest and Lowest Cost is approximately $600.00 to save you 30 hours of work. Working with kits also insures fewer mistakes in the building process. Check our Kits and Parts Price Page for more information.

See our Kayak Accessory Page to order T-Shirts and PFD's for your dog. We will be adding more product soon.

Be sure to watch our electric kayak video on YouTube:

Electric Hands-Free Fishing Kayak Video

Hit Counter

Send mail to winchuckriver@charter.net with questions or comments about this web site.
Copyright © 2007 Kingfisher Electric Boats
Last modified: 09/22/07